Material supply for contractors, distributors & fabricators · USA & Canada
Pickup: Paterson, NJMon-Fri 8-5 ET+1 (201) 723-8804info@nordicnorden.com

Steel Framing Calculators

Quick estimates for studs, track, screws, weights, trucks and coil, then send the lines straight to a quote.

Estimates only. Estimates for budgeting and ordering only. They do not replace a takeoff from the drawings or structural design. Verify quantities, sizes and weights with the engineer of record and the supplier before ordering.

Calculator 1

Stud & track takeoff

Studs, top and bottom track for straight wall runs.

Result (estimate)

Review quote
Formulas & assumptions
  • Studs per wall = ⌈wall length × 12 ÷ spacing⌉ + 1 (one stud at each end).
  • Total studs = (Σ studs per wall + openings × extra studs per opening) × (1 + waste %), rounded up. Corners, intersections, headers, sills, cripples, bracing and bridging are not included, add them as extra lines.
  • Stud length = the next standard stock length (8, 9, 10, 12, 14, 16, 20 ft) at or above the wall height, unless you choose one.
  • Track = 2 × total wall length (top + bottom) × (1 + waste %), divided into 10' or 12' pieces, rounded up. Openings are not deducted (track is usually run through and cut out).
  • Only sizes and gauges in our product range are offered. Weight uses the published weight per foot of the stud and the same-depth, same-gauge track (supplier data); structural studs use the narrowest flange we stock for that depth.
Calculator 2

Screw estimate

Framing screws for stud-to-track connections, plus optional gypsum board and drywall screws.

Result (estimate)

Formulas & assumptions
  • Framing screws = studs × screws per stud × (1 + waste %). The default of 4 assumes one screw through each flange at the top and bottom track. Bracing, bridging, clips and headers need more.
  • Gypsum sheets = wall area × sides ÷ sheet area × (1 + waste %), rounded up.
  • Drywall screws = board area × screws per sq ft × (1 + waste %). The default of 1 per sq ft (about 32 per 4' × 8' sheet) is a common rule of thumb for walls with screws at 12" o.c. in the field and 8" at edges. Ceilings, fire-rated or multi-layer assemblies need more. Follow the assembly listing.
  • Boxes = screws ÷ screws per box, rounded up. Estimates only, screw type and length depend on steel thickness and board layers.
Calculator 3

Weight per designation

Weight per foot, per piece, per order and per bundle for the studs, track and channels we supply.

Result (estimate)

Formulas & assumptions
  • Only sections in our product range are listed. Weight per foot is the published value (supplier data: product data sheets, evaluation report and catalogs). One size without a published sheet (350S125-30) is calculated from SSMA geometry as below.
  • Steel area A = design thickness t × centerline length of the section. Stud: (D − t) + 2(B − t) + 2(lip − t/2) − 4·(2 − π/2)(R + t/2). Track: (D + t) + 2B − 2·(2 − π/2)(R + t/2). D = web depth, B = flange width, R = inside corner radius per thickness (see thickness table).
  • Weight per foot = A × 12 in × 0.2836 lb/in³ (steel, 490 lb/ft³). Base steel only, galvanizing not included (G60 adds roughly 1-2 % on thin sections).
  • The same formula reproduces the published weights of our range within ±4 % (145 of 148 sections; three 4" structural tracks with a wider leg differ by 8 %) and the SSMA Product Technical Guide within ±2 %.
  • Bundle size varies by producer, depth and gauge. The pieces-per-bundle value is an editable assumption.
Calculator 4

Truckload estimator

How many trucks an order needs by weight.

Result (estimate)

Formulas & assumptions
  • Trucks = ⌈total weight ÷ payload per truck⌉. 48,000 lb is a typical legal payload for a tractor and 53' flatbed under the 80,000 lb federal gross limit. Actual payload depends on the tractor and trailer weight and on state rules.
  • Volume, bundle stacking and load securement can limit a load before weight does, especially for light-gauge drywall studs. Pieces longer than the deck need an oversize permit or special trailer.
  • 1 short ton = 2,000 lb, 1 metric tonne = 2,204.6 lb.
Calculator 5

Coil & sheet weight

Weight of flat sheet, strip or a whole coil, and how many feet are in a coil of a given weight.

Result (estimate)

Formulas & assumptions
  • Weight = width × thickness × length × 0.2836 lb/in³ (1 sq ft of 1" steel plate = 40.8 lb).
  • Coil weight from diameters = π/4 × (OD² − ID²) × width × 0.2836 lb/in³. This assumes tightly wound steel, so real coils weigh slightly less. Strip length in the coil = π/4 × (OD² − ID²) ÷ thickness.
  • Coil length from weight = weight ÷ (width × thickness × 12 × 0.2836).
  • Galvanized gauge uses the manufacturers' standard gauge for galvanized sheet (e.g. 20 ga = 0.0396", 26 ga = 0.0217"), which includes the zinc coating. For painted or Galvalume products use the actual thickness.
  • PIW = pounds per inch of width.

Estimates for budgeting and ordering only. They do not replace a takeoff from the drawings or structural design. Verify quantities, sizes and weights with the engineer of record and the supplier before ordering. Questions? Call +1 (571) 283-7703 or request a quote.