Technical Data
General reference tables for cold-formed steel framing designations, thickness and coatings.
Reading an SSMA designation
Steel framing members are identified with a four-part code used across the US industry. For example, 362S125-33 means:
| Part | Example | Meaning |
|---|---|---|
| Web depth | 362 | Web depth in 1/100 inch: 3.62 = 3-5/8" |
| Style | S | Member type (see table below) |
| Flange width | 125 | Flange width in 1/100 inch: 1.25 = 1-1/4" |
| Thickness | 33 | Minimum base-metal thickness in mils (1 mil = 1/1000 inch) |
Member style codes
| Code | Member |
|---|---|
| S | Stud or joist with return lips (C-section) |
| T | Track (U-section without lips) |
| U | U channel / cold rolled channel |
| F | Furring (hat) channel |
| L | Angle |
Thickness reference
Thickness is ordered in mils. Gauge numbers are shown for reference only; the design thickness is used in calculations and the minimum thickness (95% of design) is the least thickness acceptable on delivery.
| Mils | Ref. gauge | Design thickness (in) | Minimum thickness (in) | Inside corner radius (in) |
|---|---|---|---|---|
| 18 | 25 | 0.0188 | 0.0179 | 0.0843 |
| 27 | 22 | 0.0283 | 0.0269 | 0.0796 |
| 30 | 20 (drywall) | 0.0312 | 0.0296 | 0.0781 |
| 33 | 20 (structural) | 0.0346 | 0.0329 | 0.0764 |
| 43 | 18 | 0.0451 | 0.0428 | 0.0712 |
| 54 | 16 | 0.0566 | 0.0538 | 0.0849 |
| 68 | 14 | 0.0713 | 0.0677 | 0.1069 |
| 97 | 12 | 0.1017 | 0.0966 | 0.1525 |
| 118 | 10 | 0.1242 | 0.1180 | 0.1863 |
Web depth and flange designators
| Designator | Web depth |
|---|---|
| 162 | 1-5/8" |
| 250 | 2-1/2" |
| 350 | 3-1/2" |
| 362 | 3-5/8" |
| 400 | 4" |
| 550 | 5-1/2" |
| 600 | 6" |
| 800 | 8" |
| 1000 | 10" |
| 1200 | 12" |
| Designator | Flange | Typical use |
|---|---|---|
| 125 | 1-1/4" | Non-structural studs and track legs |
| 137 | 1-3/8" | Studs (some sizes) |
| 162 | 1-5/8" | Structural studs |
| 200 | 2" | Structural studs, joists |
| 250 | 2-1/2" | Structural studs, joists |
| 300 | 3" | Heavy structural members |
Common non-structural designations
Typical interior stud and track designations, 33 ksi, G40 minimum coating.
| Web | 18 mil stud | 30 mil stud | 33 mil stud | Track |
|---|---|---|---|---|
| 1-5/8" | 162S125-18 | 162S125-30 | 162S125-33 | 162T125-18/30/33 |
| 2-1/2" | 250S125-18 | 250S125-30 | 250S125-33 | 250T125-18/30/33 |
| 3-1/2" | 350S125-18 | 350S125-30 | 350S125-33 | 350T125-18/30/33 |
| 3-5/8" | 362S125-18 | 362S125-30 | 362S125-33 | 362T125-18/30/33 |
| 4" | 400S125-18 | 400S125-30 | 400S125-33 | 400T125-18/30/33 |
| 6" | 600S125-18 | 600S125-30 | 600S125-33 | 600T125-18/30/33 |
EQ (equivalent gauge) studs and track use proprietary high-strength sections; specify the EQ designation (e.g. EQ 25, EQ 20) together with the web depth.
Common structural designations
Structural studs and track, 33 ksi (33-43 mil) or 50 ksi (54-97 mil), G60 coating, sized by the engineer of record.
| Web | 1-5/8" flange stud | 2" flange stud | 2-1/2" flange stud | Track legs |
|---|---|---|---|---|
| 2-1/2" | 250S162-33 … -97 | 250S200-33 … -97 | 250S250-43 … -97 | 250T125 / T150 / T200 |
| 3-5/8" | 362S162-33 … -97 | 362S200-33 … -97 | 362S250-43 … -97 | 362T125 / T150 / T200 |
| 4" | 400S162-33 … -97 | 400S200-33 … -97 | 400S250-43 … -97 | 400T125 / T150 / T200 |
| 5-1/2" | 550S162-33 … -97 | 550S200-33 … -97 | 550S250-43 … -97 | 550T125 / T150 / T200 |
| 6" | 600S162-33 … -97 | 600S200-33 … -97 | 600S250-43 … -97 | 600T125 / T150 / T200 |
| 8" | 800S162-33 … -97 | 800S200-33 … -97 | 800S250-43 … -97 | 800T125 / T150 / T200 |
| 10" | 1000S162-33 … -97 | 1000S200-33 … -97 | 1000S250-43 … -97 | 1000T125 / T150 / T200 |
| 12" | 1200S162-33 … -97 | 1200S200-33 … -97 | 1200S250-43 … -97 | 1200T125 / T150 / T200 |
Galvanized coating designations
| Designation | Total both sides (oz/ft²), min. triple-spot | Metric equivalent | Typical use |
|---|---|---|---|
| G40 | 0.40 | Z120 | Interior non-structural framing |
| G60 | 0.60 | Z180 | Structural framing, exterior walls |
| G90 | 0.90 | Z275 | Severe exposure, coastal, specified jobs |
These tables are general industry reference data for orientation only. Always follow the project drawings, specifications and the engineer of record. Mill test reports and ASTM C645 / A1003 compliance documents are available on request.